View CM2576_250767.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CM2576
3A STEP DOWN VOLTAGE REGULATOR
GENERAL DESCRIPTION
The CM2576 series are step-down switching regulators with all required active functions. It is capable of driving 3A load with excellent line and load regulations. These devices are available in fixed output voltages of 3.3V, 5V, and an adjustable output version. The CM2576 series offers a high-efficiency replacement for popular three-terminal linear regulators. Also it requires a minimum number of external components. It substantially not only reduces the area of board size but also the size of the heat sink, and in some cases no heat sink is required. 4% tolerance on output voltage within specified input voltages and output load conditions is guaranteed. Also, the oscillator frequency accuracy is within 10%. External shutdown is included, featuring 70A (typical) standby current. The output switch includes cycle-by-cycle current limiting, as well as thermal shutdown for full protection under fault conditions.
FEATURES
! ! ! ! ! ! ! ! ! Guaranteed 3A output current 3.3V, 5V, and adjustable versions Wide input voltage range, up to 40V Internal oscillator of 52KHz fixed frequency Wide adjustable version output voltage range, from 1.23V to 37V4% max over line and load conditions Low standby current, typ. 70A, at shutdown mode Requires only 4 external components Thermal shutdown and current limit protection P+ product enhancement tested
APPLICATIONS
! ! ! ! LCD Monitors ADD-ON Cards Switching Regulators High Efficiency Step-Down Regulators Efficient Pre-regulator for Linear Regulators
ORDERING INFORMATION
Package Type TO-220 CM2576SCN220 CM2576ZJCN220 CM2576CN220 TO-263 CM2576SCN263 CM2576ZJCN263 CM2576CN263 Temperature Range -40 ~ +125 -40 ~ +125 -40 ~ +125 Output Voltage 3.3V 5.0V ADJ.
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 1
CM2576
3A STEP DOWN VOLTAGE REGULATOR
PIN CONFIGURATION
TO-220 Top View TO-263 Top View
E N A B LE
5 4 3 2 1
FB GND VOUT V IN
VOUT
GND
FB 4
12
3
5
ABSOLUTE MAXIMUM RATINGS
Input Voltage (VPOWER) ............................................................... +45V
ENABLE Pin Input Voltage ............................................ -0.3V VVIN
Operating Junction Temperature Range, TJ ..................... 0 to +150 Storage Temperature .................................................. -65 to +150 Lead Temperature (10 sec.) ......................................................... 260
POWER DISSIPATION TABLE
Package TO-220 TO-263 JA (/W) 45 45 Derating factor (mW/) TA >= 25 22.2 22.2 TA <= 25 Power rating (mW) 2775 2775 TA = 70 TA = 85 Power rating (mW) Power rating (mW) 1776 1443 1776 1443
Note: 1. JA : Thermal Resistance-Junction to Ambient, DF: Derating factor, PO: Power consumption.
2.
Junction Temperature Calculation: TJ = TA + (PD x JA ), PO = DF x (TJ - TA) The JA numbers are guidelines for the thermal performance of the device/PC-board system. All of the above assume no ambient airflow. JT : Thermal Resistance-Junction to Ambient, TC: case (Tab) temperature, TJ = TC + (PD x JA )
RESOMMENDED OPERATING CONDITIONS
Parameter Input Voltage (VIN) Temperature Range Symbol VIN TJ Min. -40 Typ. Max 40 125 Units V
2003/08/07 Preliminary Rev. 1.1
EN ABLE
VIN
Champion Microelectronic Corporation
Page 2
CM2576
3A STEP DOWN VOLTAGE REGULATOR
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at IOUT = 0mA, and TJ = +25; unless otherwise noted CM2576 Min. 3.234 4.900 3.168 4.800 3.135 4.750 1.217 1.193 1.180 Typ. 3.300 5.000 3.300 5.000 3.300 5.000 1.230 1.230 1.230 75 77 77 47 42 52 52 5 70 TJ=25 -40<=TJ<=125 TJ=25 -40<=TJ<=125 Note 5 Note 2,4 Note 3 VIH (VOUT =0V) TJ=25 -40<=TJ<=125 VOUT =0V VOUT =-1V TJ=25 -40<=TJ<=125 TJ=25 -40<=TJ<=125 12 0 2.2 2.4 1.2 1.0 0.8 30 10 93 4.2 3.5 98 7 7.2 0.3 9 1.4 8.8 9.0 2 20 50 1.4 58 63 10 200 1.8 2.0 100 500 TJ=25 -40<=TJ<=125 Note 3 Max. 3.366 5.100 3.432 5.200 3.482 5.250 1.243 1.267 1.286 Parameter Output Voltage (Note 1) Output Voltage (Note 1) Output Voltage (Note 1) Feedback Voltage (Note 1) Feedback Voltage (Note 1) Feedback Voltage (Note 1) Efficiency Device CM2576S CM2576ZJ CM2576S CM2576ZJ CM2576S CM2576ZJ CM2576 (Adj) CM2576 (Adj) CM2576 (Adj) CM2576S CM2576ZJ CM2576(adj) Oscillator Frequency Quiescent Current Standby Current Saturation Voltage Feedback Bias Current Duty Cycle (ON) Current Limit Output Leakage Current Note 2 Test Conditions Test circuit of Figure 1 6V<=VIN <=40V 8V<=VIN <=40V 6V<=VIN <=40V 8V<=VIN <=40V Test circuit of Figure 2 8V<=VIN <=40V, VOUT =5V Test circuit of Figure 2 8V<=VIN <=40V, VOUT =5V Test circuit of Figure 2 ILOAD =3A ILOAD =3A, VOUT =5V 0.5A<=ILOAD <=3A 0.5A<=ILOAD <=3A, -40<=TJ<=125 Test circuit of Figure 1 VOUT =5V 0.5A<=ILOAD <=3A 0.5A<=ILOAD <=3A, -40<=TJ<=125 Unit V V V V V V V V V % % kHz mA A V nA % A mA V V A
ENABLE = 5V
ILOAD =3A (Note 4) VOUT =5V (Adj. Version only)
ENABLE Threshold Voltage
VIL (VOUT = Normal Output Voltage)
ENABLE Input Current
IIH (ENABLE = 5V) IIH (ENABLE = 0V)
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 3
CM2576
3A STEP DOWN VOLTAGE REGULATOR
Note 1: External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. Refer to Application Information for details. Note 2: The oscillator frequency reduces to approximately 11KHz in the event of fault conditions, such as output short or overload. And the regulated output voltage will drop approximately 40% from the nominal output voltage. This self-protection feature lowers the average power dissipation by lowering the minimum duty cycle from 5% down to approximately 2%. Note 3: For these parameters, FB is removed from VOUT and connected to +12V to force the output transistor OFF. Note 4: VOUT pin sourcing current. No diode, inductor or capacitor connect to VOUT. Note 5: FB is removed from VOUT and connected to 0V.
BLOCK DIAGRAM
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 4
CM2576
3A STEP DOWN VOLTAGE REGULATOR
APPLICATION CIRCUIT
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 5
CM2576
3A STEP DOWN VOLTAGE REGULATOR
TYPICAL CHARACTERISTICS
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 6
CM2576
3A STEP DOWN VOLTAGE REGULATOR
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 7
CM2576
3A STEP DOWN VOLTAGE REGULATOR
APPLICATION INFORMATION
It is required that VIN must be bypassed with at least a 100uF electrolytic capacitor for stability. Also, it is strongly recommended the capacitor's leads must be dept short, and located near the regulator as possible. For low operating temperature range, for example, below -25, the input capacitor value may need to be larger. This is due to the reason that the capacitance value of electrolytic capacitors decreases and the ESR increases with lower temperatures and age. Paralleling a ceramic or solid tantalum capacitor will increase the regulator stability at cold temperatures. Output Capacitors (COUT) An output capacitor is also required to filter the output voltage and is needed for loop stability. The capacitor should be located near the CM2576 using short PC board traces. Low ESR types capacitors are recommended for low output ripple voltage and good stability. Generally, low value or low voltage (less than 12V) electrolytic capacitors usually have higher ESR numbers. For example, the lower capacitor values (220uF - 1000uF) will yield typically 50mV to 150mV of output ripple voltage, while larger-value capacitors will reduce the ripple to approximately 20mV to 50mV. The amount of output ripple voltage is primarily a function of the ESR (Equivalent Series Resistance) of the output capacitor and the amplitude of the inductor ripple current (IIND). Output Ripple Voltage = (IIND) x (ESR of COUT) Some capacitors called "high-frequency", "low-inductance", or "low-ESR" are recommended to use to further reduce the output ripple voltage to 10mV or 20mV. However, very low ESR capacitors, such as Tantalum capacitors, should be carefully evaluated. Catch Diode This diode is required to provide a return path for the inductor current when the switch is off. It should be located close to the CM2576 using short leads and short printed circuit traces as possible. To satisfy the need of fast switching speed and low forward voltage drop, Schottky diodes are widely used to provide the best efficiency, especially in low output voltage switching regulators (less than 5V). Besides, fast-Recovery, high-efficiency, or ultra-fast recovery diodes are also suitable. But some types with an abrupt turn-off characteristic may cause instability and EMI problems. A fast-recovery diode with soft recovery characteristics is better choice.
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 8
CM2576
3A STEP DOWN VOLTAGE REGULATOR
Output Voltage Ripple and Transients The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. The output ripple voltage of a switching power supply will contain a sawtooth ripple voltages at the switcher frequency, typically about 1% of the output voltages, and may also contain short voltage spikes of the sawtooth waveform. Due to the fast switching action, and the parasitic inductance of the output filter capacitor, there is voltage spikes presenting at the peaks of the sawtooth waveform. Cautions must be taken for stray capacitance, wiring inductance, and even the scope probes used for transients evaluation. To minimize these voltage spikes, shortening the lead length and PCB traces is always the first thought. Further more, an additional small LC filter (30uH & 100uF) (as shown in Figure 3) will possibly provide a 10X reduction in output ripple voltage and transients.
Inductor Selection The CM2576 can be used for either continuous or discontinuous modes of operation. Each mode has distinctively different operating characteristics, which can affect the regulator performance and requirements. With relatively heavy load currents, the circuit operates in the continuous mode (inductor current always flowing), but under light load conditions, the circuit will be forced to the discontinuous mode (inductor current falls to zero for a period of time). For light loads (less than approximately 300mA) it may be desirable to operate the regulator in the discontinuous mode, primarily because of the lower inductor values required for the discontinuous mode. Inductors are available in different styles such as pot core, toriod, E-frame, bobbin core, et., as well as different core materials, such as ferrites and powdered iron. The least expensive, the bobbin core type, consists of wire wrapped on a ferrite rod core. This type of construction makes for an inexpensive inductor, but since the magnetic flux is not completely contained within the core, it generates more electromagnetic interference (EMI). This EMI can cause problems in sensitive circuits, or can give incorrect scope readings because of induced voltages in the scope probe.
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 9
CM2576
3A STEP DOWN VOLTAGE REGULATOR
An inductor should not be operated beyond its maximum rated current because it may saturate. When an inductor begins to saturate, the inductance decreases rapidly and the inductor begins to look mainly resistive (the DC resistance of the winding). This will cause the switch current to rise very rapidly. Different inductor types have different saturation characteristics, and this should be well considered when selecting as inductor. Feedback Connection For fixed output voltage version, the FB (feedback) pin must be connected to VOUT. For the adjustable version, it is important to place the output voltage ratio resistors near CM2576 as possible in order to minimize the noise introduction.
ENABLE
It is required that the ENABLE must not be left open. For normal operation, connect this pin to a "LOW" voltage (typically, below 1.6V). On the other hand, for standby mode, connect this pin with a "HIGH" voltage. This pin can be safely pulled up to +VIN without a resistor in series with it. Grounding To maintain output voltage stability, the power ground connections must be low-impedance. For the 5-lead TO-220 and TO-263 style package, both the tab and pin 3 are ground and either connection may be used. Heatsink and Thermal Consideration Although the CM2576 requires only a small heatsink for most cases, the following thermal consideration is important for all operation. With the package thermal resistances JA and JC, total power dissipation can be estimated as follows: PD = (VIN x IQ) + (VOUT / VIN)(ILOAD x VSAT); When no heatsink is used, the junction temperature rise can be determined by the following: TJ = PD x JA; With the ambient temerpature, the actual junction temperature will be: TJ = TJ + TA; If the actual operating junction temperature is out of the safe operating junction temperature (typically 125), then a heatsink is required. When using a heatsink, the junction temperature rise will be reduced by the following: TJ = PD x (JC + interface + Heatsink); Also one can see from the above, it is important to choose an heatsink with adequate size and thermal resistance, such that to maintain the regulator's junction temperature below the maximum operating temperature.
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 10
CM2576
3A STEP DOWN VOLTAGE REGULATOR
PACKAGE DIMENSION
TO-220 (N220)
B
F
C S
T
A B C
A
D F G J
12345
K N R S T
K
G N
D
R J
TO-263 (N263)
C A D I K G F L E
2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation
B
Page 11
CM2576
3A STEP DOWN VOLTAGE REGULATOR
IMPORTANT NOTICE
Champion Microelectronic Corporation (CMC) reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. A few applications using integrated circuit products may involve potential risks of death, personal injury, or severe property or environmental damage. CMC integrated circuit products are not designed, intended, authorized, or warranted to be suitable for Use of CMC products in such applications is In order to minimize risks associated with the customer's applications, the use in life-support applications, devices or systems or other critical applications. understood to be fully at the risk of the customer. customer should provide adequate design and operating safeguards.
HsinChu Headquarter
5F, No. 11, Park Avenue II, Science-Based Industrial Park, HsinChu City, Taiwan T E L : +886-3-567 9979 F A X : +886-3-567 9909
Sales & Marketing
11F, No. 306-3, SEC. 1, Ta Tung Road, Hsichih, Taipei Hsien 221, Taiwan T E L : +886-2-8692 1591 F A X : +886-2-8692 1596
2003/08/07 Preliminary Rev. 1.1
Champion Microelectronic Corporation
Page 12

▲Up To Search▲

Price & Availability of CM2576

	To Download CM2576 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .